PDA

View Full Version : drive shaft

SleepRob89
08-20-2005, 10:36 PM
i need a drive shaft for my 89 wrangler it is lifted 4 inch and 2 body let me know what you got and how much please i need one or im not going anywhere fast or slow
XEON
08-20-2005, 10:47 PM
I think I might have one. Its from an 88 Wrangler with a 4banger manual. Let me check my garage tomarrow.
xjbob
09-06-2005, 11:35 AM
If you give me a measurement I will check my pile too
SleepRob89
09-11-2005, 11:00 AM
how should i get the size from what point to what point let me know my jeep is a 6cyl so i dont know if the 4cyl will work but you may know more then i do im sure thanks for the help
ROCKREADYXJ
09-13-2005, 10:13 AM
They are a different length. Do you have one now that you can measure? I have both but not sure between the the 6 or the for they are not labled.
XEON
09-13-2005, 12:13 PM
They are a different length. Do you have one now that you can measure? I have both but not sure between the the 6 or the for they are not labled.

I would assume the 4 banger one would be longer then the 6. If its an automatic it would be shorty because the autos are alittle longer transmission I think. Correct me if I am wrong?
ROCKREADYXJ
09-13-2005, 12:49 PM
They are a different length. Do you have one now that you can measure? I have both but not sure between the the 6 or the for they are not labled.

I would assume the 4 banger one would be longer then the 6. If its an automatic it would be shorty because the autos are alittle longer transmission I think. Correct me if I am wrong?

yes and no there are 4 different shafts 4cyl manual 4 cyl auto 6cyl auto 6 cyl man I have two marked 6 cyl but no trans so a measure ment would help me the best.
SleepRob89
09-13-2005, 06:06 PM
They are a different length. Do you have one now that you can measure? I have both but not sure between the the 6 or the for they are not labled.

I would assume the 4 banger one would be longer then the 6. If its an automatic it would be shorty because the autos are alittle longer transmission I think. Correct me if I am wrong?

yes and no there are 4 different shafts 4cyl manual 4 cyl auto 6cyl auto 6 cyl man I have two marked 6 cyl but no trans so a measure ment would help me the best.


ok well i got 10in form end to end i measured it from the bottom of where the u-joint is suposto go to the other one is idk if this would help you but like this part >> )===( <<
SleepRob89
09-13-2005, 06:06 PM
my jeep is a 6cyl not a 4
ROCKREADYXJ
09-14-2005, 08:13 AM
a better measurement would be from center of u-joint to center of u-joint. I think that I have it here.
SleepRob89
09-14-2005, 02:56 PM
a better measurement would be from center of u-joint to center of u-joint. I think that I have it here.


the one u have is stock?? :?:
ROCKREADYXJ
09-15-2005, 12:59 PM
yes I have a pile of them that are unmarked. If you want to measure I will be glad to see if I have one that fits
SleepRob89
09-15-2005, 04:44 PM
ok well i got 13in rough let me know i heed one that is like maybe 14 or 15 or maybe 16 i have the stock one but i need the one to fit the lift my yoke is sticking out and i know that is not a good thing so let me know
ROCKREADYXJ
09-20-2005, 09:29 AM
Give me a call and I will help you with your driveshaft problem.

Joe
SleepRob89
09-20-2005, 10:03 PM
:lol: thanks guys for all your help i took it to this driveshaft place on rt 17 in rutherford and the guy made me one :lol: THANKS TO ALL



no if only you guys can help me with getting a fender before i have to take it to painting that would be great