Whats your next project?

[XEON]

What is your next project on your rig?

My next project:

~Fix idle issues
~Open up rear end check things out and replace fluids
~Clean the Jeep
~Check squeeking on the front end
~Other misc stuff

8) :wtg:

[dmxjg35]

new rear spring packs, my add-a-leaf is sagging of course, got a clunk in the front end, both headlights just blew out tonite :( and maybe a new rear axel if i can find one

[badzook]

new rear spring packs, my add-a-leaf is sagging of course, got a clunk in the front end, both headlights just blew out tonite :( and maybe a new rear axel if i can find one

Hey,

If you need help installing the rear let me know...

It seems I'm getting pretty good at doing that kind of thing lately..

I'm installing another rear in My XJ . The weak d 35 C is wiped out.

I'm looking for a D44 with no luck so far...

Does anybody know if the backing plates will bolt up from D35c to D44?

And... what about the tone rings???

I can't get an inspection sticker with the ABS lite on if I disable the ABS...Bummer...

badzook. :roll: :roll:

[wrangler]

:offtopic:

[badzook]

My next project:

~Fix idle issues


Idle problems can be lots of things..

Start with a complete fresh Tune - Up.
Gap those Plugs Correctly....
Here's a few tricks for you.

1) Disconnect the battery for 24 hours. It erases the memory and resets the strategies...
2) Use your garden hose and gently spray water around the intake while the engine is running. If you have an intake leak it will show up by changing the idle pattern. Do this with the air cleaner in place and do NOT let water go down the intake.
3) Remove and clean the throttle body and idle control motor. ( Do not spray Carb cleaner in the IAC ) Use Carb Cleaner to clean the throttle plates and passages..

Good Luck..
badzook 8) 8)

[NYWheeler]

Lift, Locker, and Tires on the XJ.

[wrangler]

My project now is to install a new thermastat. I found my jeep had a 210degree thermostat in it. (way to hot) Seems like an easy task aside from that i cracked the thermostat housing which leaves my jeep undrivable. Does any one know were to get a new thermostat housing for the 2.5L YJ (88') 4cyl? On quadratic they only sell one for the 6 cyl.

Thanks,
Cody

[XEON]

My project now is to install a new thermastat. I found my jeep had a 210degree thermostat in it. (way to hot) Seems like an easy task aside from that i cracked the thermostat housing which leaves my jeep undrivable. Does any one know were to get a new thermostat housing for the 2.5L YJ (88') 4cyl? On quadratic they only sell one for the 6 cyl.

Thanks,
Cody

Local auto parts store :D

I think I have a 180 in my YJ 4 banger... The motor should be running at 210 when warm.

[wrangler]

Thanks,
I already bought a 180 stat but now i just need the housing. I'll try napa.

[we3jeepers]

project huh......ok
current project (clicky) (http://community.webshots.com/album/271648989CLhbyi)

this has been put my jeep on the back burner :lol:
its the 1.76 acres of land i bought last month
its really close to the river and 1.5 miles from town
6 min. from the g/f's work and 12 min. from mine

i currenty live in a trailer park but will be moving my trailer out of the park and up to the land

i have purchased a new Husqvarna 55 Rancher of ebay for 275 shipped
http://i6.ebayimg.com/01/i/03/78/10/5f_1_b.JPG

and have been useing that and my brushcutter to clear the land
i got almost all of the brush taken care of and have cut down 8-10 smaller trees (10-12" thick 30' high)

the only chance i get to go up there are Fridays, Saturdays and my G/F's days off
i work 3rd shift and she works 2nd so when she is working i watch our 3 year old daughter

i didnt work at all last week cause i was to sore (got snipped on monday)

i will be back at it friday, sat. and sunday

[Freebird01]

ive got a few things on the burner....

i finally got a good yota driveshaft that i will be dropping off tomorrow to get shortened for my zuk. i need to try and come up with adapters or buy a set of rockrat adapters...

i still got to take my front axle out and redrill my perches and plates to move it forward to correct my steering geometry

i got to bring home the 1980 CJ5 project i just bought this comming saturday...

i need to get the paper work done my my bike since i finally got the title in the mail today...

sheesh....

*edit*

i also forgot i have a pair or turn signals to swap into my motorcycle yet...

[matt6669]

hmm projects i got tons!!!

lift kit
tires
sye and driveshaft
rocker rails
front bumper
the list just keeps going on and on and on

its a never ending project

[Chris 88 YJ]

- get tender coils for my rear shocks. the springs fall apart unloaded. mabye change the upper spring rate too

- build bump stops and a center limiting cable for the rear suspension

- replace the driver's side leaf spring that I bent on the Neuroc's course last weekend.

- move my seats further back on the cage

- continue to wheel it as much as possible 8)

[bondo303]

I have many projects waiting to happen.

In my shed,
- 4.56 gears/install kits/carriers for the front & rear
- 1" body lift
- M.O.R.E MML

In the mail,
- all the parts needed for flush mounts for the rear (LED)
- armor for the rear corners

waiting for $$$
- tires
- suspension