SleepRob89
06-20-2007, 10:55 AM
NOT SELLING ANYMORE ONCE AGAIN
-89 YJ
-97k original miles on the body
- old v6 is available if you would rather pay for that motor, not in best condition but when pulled, it had 97K on it.
-Half Doors
-V8 Small Block
-4" Leaf Springs (Truck Sits At 10.5" Lift 4" Leafs 5" soa 1.5 Blocks In The Rear)
-Custom Diamondplate on the hole back
-custom Led Brake Lights
-custom TJ style filler for gas
-custom Hi-Lift jack mount on hood
-custom pro comp bumper with d-ring mounts and d-rings
-6" extended flares
-custom rock sliders with step
-CB radio with 2 wipps
-newer style rollcage
-rolled on bedliner inside
-GM 10 Bolt Axles
-Wagon Wheels
-Windshield Light Mounts
-Dana 30(extra)
V8 Swap Parts
-98% Complete SBC
-Alum Radiator
-Advanced Adaptors SBC Motor (http://www.jeepforum.com/forum/showthread.php?p=3871795#)
-Chrome Headers
-Chrome Valve Cover, Air Cleaner, Dipstick, Timing Cover, Fuel (http://www.jeepforum.com/forum/showthread.php?p=3871795#)Block Off Plate,ect.
-Weld On Shock Hoops For The Front
-Auto (http://www.jeepforum.com/forum/showthread.php?p=3871795#) Floor Shifter
The YJ has absolutely no rot anywhere and barely any surface rust. The V8 was one of my old motors that I bought off aCamaro (http://www.jeepforum.com/forum/showthread.php?p=3871795#) that had been rear ended but the motor was fine. It has been rebuilt less than 5k miles ago. The motor is not in the truck. Started this project and just has far too many things going on and unfortunately cannot finish it. The truck does NOT have a t-case or trans. Here is the link to the pictures:
http://s4.photobucket.com/albums/y10...lbike/Selling/ (http://s4.photobucket.com/albums/y103/fatmanonalilbike/Selling/)
-89 YJ
-97k original miles on the body
- old v6 is available if you would rather pay for that motor, not in best condition but when pulled, it had 97K on it.
-Half Doors
-V8 Small Block
-4" Leaf Springs (Truck Sits At 10.5" Lift 4" Leafs 5" soa 1.5 Blocks In The Rear)
-Custom Diamondplate on the hole back
-custom Led Brake Lights
-custom TJ style filler for gas
-custom Hi-Lift jack mount on hood
-custom pro comp bumper with d-ring mounts and d-rings
-6" extended flares
-custom rock sliders with step
-CB radio with 2 wipps
-newer style rollcage
-rolled on bedliner inside
-GM 10 Bolt Axles
-Wagon Wheels
-Windshield Light Mounts
-Dana 30(extra)
V8 Swap Parts
-98% Complete SBC
-Alum Radiator
-Advanced Adaptors SBC Motor (http://www.jeepforum.com/forum/showthread.php?p=3871795#)
-Chrome Headers
-Chrome Valve Cover, Air Cleaner, Dipstick, Timing Cover, Fuel (http://www.jeepforum.com/forum/showthread.php?p=3871795#)Block Off Plate,ect.
-Weld On Shock Hoops For The Front
-Auto (http://www.jeepforum.com/forum/showthread.php?p=3871795#) Floor Shifter
The YJ has absolutely no rot anywhere and barely any surface rust. The V8 was one of my old motors that I bought off aCamaro (http://www.jeepforum.com/forum/showthread.php?p=3871795#) that had been rear ended but the motor was fine. It has been rebuilt less than 5k miles ago. The motor is not in the truck. Started this project and just has far too many things going on and unfortunately cannot finish it. The truck does NOT have a t-case or trans. Here is the link to the pictures:
http://s4.photobucket.com/albums/y10...lbike/Selling/ (http://s4.photobucket.com/albums/y103/fatmanonalilbike/Selling/)